karta tv + pilot = pierdzenie

Jurek - 4 Wrz 2007, 17:25

witam,
uruchamiałem ostatnio pilot do karty avermedia tv go 007. Coś tam niby
działa (przełączanie kanałów, reg. głośności) ale pojawiły się dziwne
dźwięki. O ile przy oglądaniu tv jest ok, to przy wyłączeniu okna z
tvtime z głośników słychać "pierdzenie". Przy ruszaniu myszką, przy
jakichkolwiek operacjach na dysku, nie da sie też za bardzo słuchać
muzyki...Jest tak od momentu uruchomienia pilota.
Jeśli ktoś z Was spotkałby sie juz z takim problemem to prosze o radę...

Jurek - 4 Wrz 2007, 17:28

jeszcze coś:
kartę ustawiałem zgodnie z linuxtv.org:
przy modprobe saa7134 card=44
dźwięk jest ok, nie działa pilot,
natomiast przy np:
modprobe saa7134 card=52 tuner=5
jest pilot i 'pierdzenie'

Tomasz Sałajczyk - 5 Wrz 2007, 02:04

Podejrzewam coś z przerwaniami. Co pokazuje procinfo, może któreś
przerwanie jest współdzielone.

jureko - 5 Wrz 2007, 06:36

irq  0:   1517733 timer                 irq 12:    216702 i8042
irq  1:      2787 i8042                 irq 14:     53601 ide0
irq  3:        12                       irq 16:     63135 libata
irq  4:        13                       irq 17:     32704 uhci_hcd:usb1,
uhci_
irq  6:         5 floppy [2]            irq 18:     58079 eth0
irq  7:         0 parport0              irq 19:     92103 VIA8237
irq  8:         8 rtc                   irq 20:    457061

irq  9:         0 acpi
ale nie widze tu info o karcie tv...

Tomasz Sałajczyk - 5 Wrz 2007, 06:43

dawaj lspci -v

jureko - 5 Wrz 2007, 07:16

00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400/KT600 AGP]
Host Bridge (rev 80)
         Subsystem: Giga-byte Technology GA-7VAX Mainboard
         Flags: bus master, 66MHz, medium devsel, latency 8
         Memory at d0000000 (32-bit, prefetchable) [size=128M]
         Capabilities: <access denied

00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00
[Normal decode])
         Flags: bus master, 66MHz, medium devsel, latency 0
         Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
         I/O behind bridge: 0000a000-0000afff
         Memory behind bridge: e8000000-e9ffffff
         Prefetchable memory behind bridge: d8000000-e7ffffff
         Capabilities: <access denied

00:0c.0 Multimedia controller: Philips Semiconductors SAA7130 Video
Broadcast Decoder (rev 01)
         Subsystem: Avermedia Technologies Inc Unknown device d109
         Flags: bus master, medium devsel, latency 32, IRQ 20
         Memory at ea000000 (32-bit, non-prefetchable) [size=1K]
         Capabilities: <access denied

00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID
Controller (rev 80)
         Subsystem: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller
         Flags: bus master, medium devsel, latency 32, IRQ 16
         I/O ports at b000 [size=8]
         I/O ports at b400 [size=4]
         I/O ports at b800 [size=8]
         I/O ports at bc00 [size=4]
         I/O ports at c000 [size=16]
         I/O ports at c400 [size=256]
         Capabilities: <access denied

00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
         Subsystem: Giga-byte Technology GA-7VAX Mainboard
         Flags: bus master, medium devsel, latency 32, IRQ 16
         [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
         [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
         [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
         [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
         I/O ports at c800 [size=16]
         Capabilities: <access denied

00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
         Subsystem: Giga-byte Technology GA-7VAX Mainboard
         Flags: bus master, medium devsel, latency 32, IRQ 17
         I/O ports at cc00 [size=32]
         Capabilities: <access denied

00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
         Subsystem: Giga-byte Technology GA-7VAX Mainboard
         Flags: bus master, medium devsel, latency 32, IRQ 17
         I/O ports at d000 [size=32]
         Capabilities: <access denied

00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
         Subsystem: Giga-byte Technology GA-7VAX Mainboard
         Flags: bus master, medium devsel, latency 32, IRQ 17
         I/O ports at d400 [size=32]
         Capabilities: <access denied

00:10.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 81) (prog-if 00 [UHCI])
         Subsystem: Giga-byte Technology GA-7VAX Mainboard
         Flags: bus master, medium devsel, latency 32, IRQ 17
         I/O ports at d800 [size=32]
         Capabilities: <access denied

00:10.4 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 86) (prog-if
20 [EHCI])
         Subsystem: Giga-byte Technology GA-7VAX Mainboard
         Flags: bus master, medium devsel, latency 32, IRQ 17
         Memory at ea001000 (32-bit, non-prefetchable) [size=256]
         Capabilities: <access denied

00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[KT600/K8T800/K8T890 South]
         Subsystem: Giga-byte Technology GA-7VT600 Motherboard
         Flags: bus master, stepping, medium devsel, latency 0
         Capabilities: <access denied

00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235/8237 AC97 Audio Controller (rev 60)
         Subsystem: Giga-byte Technology GA-7VAX Onboard Audio (Realtek
ALC650)
         Flags: medium devsel, IRQ 19
         I/O ports at dc00 [size=256]
         Capabilities: <access denied

00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
RTL-8139/8139C/8139C+ (rev 10)
         Subsystem: Giga-byte Technology GA-7VM400M/7VT600 Motherboard
         Flags: bus master, medium devsel, latency 32, IRQ 18
         I/O ports at e000 [size=256]
         Memory at ea002000 (32-bit, non-prefetchable) [size=256]
         Capabilities: <access denied

01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon
9200] (rev 01) (prog-if 00 [VGA])
         Subsystem: PC Partner Limited Sapphire Radeon 9200
         Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 20
         Memory at d8000000 (32-bit, prefetchable) [size=128M]
         I/O ports at a000 [size=256]
         Memory at e9000000 (32-bit, non-prefetchable) [size=64K]
         [virtual] Expansion ROM at e8000000 [disabled] [size=128K]
         Capabilities: <access denied

01:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200]
(Secondary) (rev 01)
         Subsystem: PC Partner Limited Sapphire Radeon 9200
         Flags: bus master, 66MHz, medium devsel, latency 32
         Memory at e0000000 (32-bit, prefetchable) [size=128M]
         Memory at e9010000 (32-bit, non-prefetchable) [size=64K]
         Capabilities: <access denied

widzĂŞ Âże pokrywa siĂŞ IRQ20, ale tak jak jest teraz to nie pierdzi,
przeÂładuje moduÂł do karty na 'wadliwe' ustawienia i dam jeszcze raz.

jureko - 5 Wrz 2007, 07:36

zrobiÂłem jeszcze dmesg, i tak:
  - dla dobrego dÂźwiĂŞku ale bez pilota jest

[ 9009.322120] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 9009.323164] saa7130[0]: found at 0000:00:0c.0, rev: 1, irq: 20,
latency: 32, mmio: 0xea000000
[ 9009.323179] saa7130[0]: subsystem: 1461:d109, board: Empire PCI
TV-Radio LE [card=44,insmod option]
[ 9009.323945] saa7130[0]: board init: gpio is 10704

[ 9009.444519] tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 and
compatibles))
[ 9009.444529] tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 and
compatibles))
[ 9009.495744] saa7130[0]: i2c eeprom 00: 61 14 09 d1 ff ff ff ff ff ff
ff ff ff ff ff ff
[ 9009.495758] saa7130[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 9009.495767] saa7130[0]: i2c eeprom 20: 13 02 ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 9009.495774] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 9009.495782] saa7130[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 9009.495790] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 9009.495797] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 9009.495805] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 9009.519056] saa7130[0]/irq[10,2174077]: r=0x20 s=0x10 PE
[ 9009.519066] saa7130[0]/irq: looping -- clearing PE (parity error!)
enable bit
[ 9009.526218] saa7130[0]: registered device video0 [v4l2]
[ 9009.526341] saa7130[0]: registered device vbi0
[ 9009.526446] saa7130[0]: registered device radio0

- dla problemów z dÂźwiekiem (ale dÂźwiĂŞk dla samej tv jest ok), ale
dziaÂła pilot

[ 8875.492857] saa7130/34: v4l2 driver version 0.2.14 loaded
[ 8875.493499] saa7130[0]: found at 0000:00:0c.0, rev: 1, irq: 20,
latency: 32, mmio: 0xea000000
[ 8875.493512] saa7130[0]: subsystem: 1461:d109, board: AverMedia AverTV
Studio 305 [card=35,insmod option]
[ 8875.493851] saa7130[0]: board init: gpio is 107c4
[ 8875.494613] input: saa7134 IR (AverMedia AverTV St as /class/input/input7

[ 8875.612278] tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 and
compatibles))
[ 8875.612286] tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 and
compatibles))
[ 8875.663781] saa7130[0]: i2c eeprom 00: 61 14 09 d1 ff ff ff ff ff ff
ff ff ff ff ff ff
[ 8875.663795] saa7130[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 8875.663804] saa7130[0]: i2c eeprom 20: 13 02 ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 8875.663811] saa7130[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 8875.663819] saa7130[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 8875.663827] saa7130[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 8875.663834] saa7130[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 8875.663842] saa7130[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff
ff ff ff ff ff ff
[ 8875.680716] saa7130[0]/irq[10,2140578]: r=0x20 s=0x10 PE
[ 8875.680728] saa7130[0]/irq: looping -- clearing PE (parity error!)
enable bit
[ 8875.693782] saa7130[0]: registered device video0 [v4l2]
[ 8875.693908] saa7130[0]: registered device vbi0
[ 8875.694021] saa7130[0]: registered device radio0

nie wiem czy z tego coÂś widaĂŚ...moÂże jeszcze popróbuje dla innych
parametrów saa7134...

Tomasz Sałajczyk - 5 Wrz 2007, 07:55

opis do Twojej karty jest tutaj
http://linuxtv.org/v4lwiki/index.php/AVerMedia_AVerTV_GO_007_FM

ładujesz nie te karty (Empire PCI TV-Radio LE i AverMedia AverTV Studio 305)

Tomasz Sałajczyk - 5 Wrz 2007, 07:58

sorki już doczytałem... faktycznie dla AVerMedia AVerTV GO 007 twoje
ustawienia są prawidłowe, sam już nie wiem...

jureko - 5 Wrz 2007, 08:11

no właśnie kiedyś walczyłem z tym jak ją ustawić, szukałem głównie po
forach zamiast u źródła - załadowałem jak na linuxtv.org i hulało, no
ale później wziąłem się za pilota...
w każdym radzie dzięki za pomoc
pozdrawiam